(A) Ribbon diagram of the crystal structure of the head to tail homodimer of FH2 domains of Bni1p (residues 1350–1760) (Xu et al. 2004) (PDB Accession Code 1UX5). The two subunits are shown in green and purple. Labels indicate the approximate positions of the lasso, flexible linker, knob, coiled-coil, and post regions of the green subunit. (B) Crystal structure of the complex of Bni1p-FH2 (residues 1350–1760) with muscle actin (Otomo et al. 2005b) (PDB Accession Code 1Y64). Three contiguous actin subunits along the filament-like polymer are shown as space-filling representation in shades of gray and blue and numbered 1 to 3 from the barbed end. Ribbon diagrams of two FH2 subunits are colored as in (A). A continuous chain of FH2 domains wraps around the actin polymer with the lasso of one FH2 subunit joined to the post of the next. For clarity the density for the linker (residues 1401–1417) is omitted. This view shows the knob of the green FH2 subunit bound in the groove between subdomains 1 and 3 of actin subunit 2, as well as the post site of the green FH2 subunit bound to subdomain 1 of actin subunit 2. The partial transparency of the actin subunits reveals the symmetrical attachments of the purple FH2 subunit to actin subunits 2 and 3. (C) Comparison of the FH2 subunits from (A) and (B). When the knob and post regions of Bni1p-FH2 (residues 1418–1760) from the homodimer (Xu et al. 2004) (red) and the cocrystal with actin (Otomo et al. 2005b) (blue) were overlaid with PYMOL using the “align” function, the positions of the lasso-linkers diverge substantially with the linker more extended in complex with actin. All images were rendered with PYMOL (Delano Scientific).

The drawing gives five steps (1–5) and transitions in a hypothetical mechanical cycle of actin subunit addition coupled to translocation of a formin FH2 dimer (green and magenta). States 5 and 4 are equivalent to states 1 and 2 but the filament is one subunit longer. The upper images for each state show a side view with the barbed end down. The lower images are views of the barbed end. The actin subunits are grey along one long pitch strand and blue along the other strand. The short-pitch helical twist of the 3 terminal barbed end subunits is either 180° as found in cocrystals of Bni1pFH2 with actin or the 167° as in the core of actin filaments. The red angle symbol indicates closed 180° conformations that do not accept subunit addition. The green angle symbol indicates open 167° conformations that permit subunit addition. Each FH2 subunit has two sites that can interact with actin: the knob (K) and post (P). Sites engaged with the filament are labeled (+). Sites dissociated from the filament are labeled (−). The flexible linkers between the two FH2 subunits are depicted as either stretched or relaxed springs. States 1 and 2 (as 5 and 4) are rapid equilibria between the open and closes states. A new actin subunit adds to open state 2 to form intermediate state 3. The leading FH2 subunit steps onto the new terminal subunit to complete the cycle. (From Paul and Pollard, Paul and Pollard 2008)

The arrangement of the GTPase-binding domain (GBD), the Diaphanous-Inhibitory Domain (DID), the Formin-homology (FH1) Domain, the Formin-homology (FH2) Domain, and Diaphanous Autoregulatory Domain (DAD), are delineated at their approximate, relative scales according to primary sequence of the full-length mDia1 formin molecule (Higgs 2005).

The schematic depicts addition of one subunit (from “n” to “n+1”) onto barbed end associated with a FH2 dimer, where the formin equilibrates between a closed state that prevents subunit addition and an open state that allows addition (Otomo et al. 2005b; Xu et al. 2004). The subunits of the two long-pitch strands of the actin filament are shown as blue or silver spheres numbered 1, 2 and 3 from the barbed end. The leading subunit of the FH2 dimer is green and the trailing subunit purple. In the closed state, the FH2 dimer is engaged at both of its knob (K) and post (P) sites to the three terminal subunits. The leading FH2 subunit binds to actin subunits 1 and 2 and the trailing subunit binds to actin subunits 2 and 3 in the closed state. To enter the open state, the trailing subunit disengages both its knob and post sites, translocates or “steps” in the barbed end direction, and reattaches only its knob to the terminal barbed end subunit. In this open state, this FH2 subunit’s post site is exposed to solution. An actin monomer in solution binds to this post site and the two terminal actin subunits to complete the cycle of subunit addition and reestablish the closed state.

Through the process of subunit addition, each state of the formin-FH1FH2-associated end is denoted by a different number. The actin filament and formin dimer subunits are colored as in Figure 3. Each FH1 domain has multiple polyproline tracks (yellow ovals). Profilin (small blue circle) binds to an actin monomer in solution (large gray circle). To complete one cycle of subunit addition, the profilin-actin complex may add onto the formin-FH1FH2-associated end via the FH1-independent pathway (1-2-3) or the FH1-dependent pathway (1-2’-3’-2-3) (Vavylonis et al. 2006). The rapid delivery step by which FH1-bound-profilin-actin is transferred directly to the FH2-associated barbed end and the resultant “ring complex” (Vavylonis et al. 2006) are labeled.