• We are sorry, but NCBI web applications do not support your browser and may not function properly. More information
Logo of nanoreslettspringer open web sitethis articlemanuscript submissionregistrationjournal front pagespringer open web site
Nanoscale Res Lett. 2009; 4(7): 665–667.
Published online Mar 24, 2009. doi:  10.1007/s11671-009-9289-7
PMCID: PMC2893791

Modulation of Transmission Spectra of Anodized Alumina Membrane Distributed Bragg Reflector by Controlling Anodization Temperature

Abstract

We have successfully prepared anodized alumina membrane distributed Bragg reflector (DBR) using electrochemical anodization method. The transmission peak of this distributed Bragg reflector could be easily and effectively modulated to cover almost any wavelength range of the whole visible spectrum by adjusting anodization temperature.

Keywords: Anodized alumina membrane, Distributed Bragg reflector, Photonic crystal, Electrochemical anodization, Anodization temperature

Introduction

Distributed Bragg reflector (DBR) is a structure, which is consisted of periodically stacked multiple layers with different refractive indices in one dimension. As one-dimensional photonic crystal (PC), it can strongly and selectively modify the propagation of the incident light. According to this outstanding optical character, DBR has attracted much more attention in recent years due to its wide applications in light filters, vertical cavity surface emitting laser, electroabsorptive reflection modulators, etc. [1-7]. Recently, Wang et al. [8] described a photonic crystal via making air pores periodically in anodic alumina membrane (AAM); however, the stop band of incident light is only modified from 450 to 525 nm by changing the chemical etching time. When the incidence angle increases progressively, a blue shift of the transmission peak emerges and the peak intensity reduces gradually [9]. It has been reported that a novel kind of DBR at low cost, named AAM DBR, was prepared based on the layer-by-layer structure in AAM by adjusting the anodizing cell voltage periodically in the process of electrochemical anodization of Al foil, and the first Bragg condition peak in transmission spectra of this AAM DBR can be modulated from 727 to 1,200 nm [10].

As known, the electrolyte temperature determines the velocity of oxidation and chemical dissolution, the surface porosity, as well as mechanical stress at the metal/oxide interface in the process of electrochemical anodization [11-13]. Nevertheless, there has been no investigation of the influence of temperature on the optical characteristics of AAM DBR up to now.

In this study, by varying the anodization temperature we could conveniently obtain the AAM DBR with the transmission peak covering almost any wavelength range of the visible light region. The variation of intensity of the transmission peak versus anodization temperature has also been investigated.

Experimental Section

For the synthesis of AAM DBR, high-purity aluminum foils (99.999%) were first degreased in acetone and ethanol, and then annealed at 500 °C under vacuum ambient (about 2 × 10−5 torr) for 5 h to remove the mechanical stress. The aluminum was electrochemically polished by a mixture of HClO4 and C2H5OH (the volume ratio is 1:9). In the process of electrochemical anodization, we made use of a computer to output a periodical cell voltage. In one period, the cell voltage increases sinusoidally from 23 to 53 V in 30 s at first, and then decreases linearly from 53 to 23 V in 3 min [8,10]. In order to precisely control the anodization temperature the electrochemical cell, which contains the Al foil, was placed in a constant temperature water tank. All the samples were electrochemically anodized for 24 h. The remaining aluminum was etched by saturated SnCl4 solution. The samples were characterized by a field-emission scanning electron microscopy (FE-SEM, Sirion 200), and the transmission spectra was measured at room temperature by a spectrophotometer (CARY 5E) with the incident light perpendicular to the AAM DBR samples.

Results and Discussions

The transmission curves of samples, which were prepared at four different temperatures, are shown in Fig. Fig.1.1. Sample 1, 2, 3, and 4 were prepared at 18, 14, 10, and 6 °C, respectively. It can be seen that when the preparation temperature decreases a blue shift of transmission peak occurs, while the transmissivity of incident light, corresponding to the first Bragg condition peak, increases simultaneously. Especially for sample 4, the stop band around 350 nm could hardly be observed and the transmission curve is similar to that of ordinary AAM. This phenomenon may be explained as follows: while the temperature decreases, either the oxide formation or chemical dissolution is decelerated, which directly induces the reducing of thickness of both main and branched channel layer (d1 and d2), furthermore the Bragg wavelength, λm, (m is the order of the Bragg condition), will become diminished according to the equation shown as below [14]:

equation image
(1)
Figure 1
The transmission spectra of AAM DBRs prepared at 18 °C (curve a), 14 °C (curve b), 10 °C (curve c) and 6 °C (curve d), respectively

where n1 and n2 stand for the refractive index of main and branched channel layer, respectively. To prove this, the samples prepared under different temperatures were characterized by FE-SEM as shown in Fig. Fig.2.2. Figure Figure2a2a shows an FE-SEM image of the sample 1 prepared at 18 °C, and Fig. Fig.2b2b corresponds to sample 2 prepared at 14 °C. It can be clearly seen that the lower the temperature was, the thinner the main and branched channel became. With the temperature decreasing to 10 °C, the main and branched channel layers turned further thinner and some branched channels began to vanish, shown in Fig. Fig.2c.2c. In Fig. Fig.2d2d corresponding to the sample prepared at 6 °C, we can observe that due to slow growth rate at low temperature most branches disappear. As a result the morphology of the channels seems the same as that of straight ones in the ordinary AAM. The distance of remaining adjacent branched channel layers bears less than 100 nm in thickness.

Figure 2
The SEM image of samples prepared ata18 °C,b14 °C,c10 °C, andd6 °C, respectively

Figure Figure3shows3shows the optical photograph of AAM DBRs prepared at different anodization temperature from 7 to 14 °C. It is clearly demonstrated that these AAM DBRs almost contain every color of the whole visible light region.

Figure 3
The optical photograph of AAM DBRs prepared for 24 h at different anodization temperatures from 7 to 14 °C

Another issue to be considered is the increasing of transmissivity as the temperature drops, which is brought by the inadequate growth of branches. It is well known that sufficiently high dielectric contrast of two different dielectric materials comprised in the photonic related structures could bring high reflectance to a certain incident light. The reflectivity of a periodical multilayer structure composed of alternating layers with different refractive indices nL and nH on the substrate with the index of nS is given as below [15]:

equation image
(2)

where the nL and nH is the refractive index of the low and high index dielectric, respectively. Here, the branched channel layer stands for low index dielectric material and the main stem layer corresponds to the high one. The M is the number of the layer pairs. Every two neighboring layers, i.e., main channel layer and branched channel layer, constitute one layer pair. In our experiment, we could consider the air play the role of substrate with nS as 1. The refractivity R is inversely proportional to the value of nL/nH, which means the transmissivity T is directly proportional to this ratio. When the anodization temperature decreases, the branched channel layers will not grow sufficiently, so the contrast of effective refractivity of two layers turns to be less. Since the ratio of nL/nH is augmented, the transmissivity of the whole structure therewith raises. Hence, the effect of inhibition to the incident light becomes weakened.

Conclusion

We have successfully prepared anodized alumina membrane distributed Bragg reflector using electrochemical anodization method. By modifying the anodization temperature, the transmission spectra of AAM DBR could be effectively modulated to cover almost any wavelength range of the whole visible spectrum.

Acknowledgments

This work was supported by the National Natural Science Foundation of China (No.50671099, 50172048, 10374090 and 10274085), Ministry of Science and Technology of China (No.2005CB623603), and Hundred Talent Program of Chinese Academy of Sciences.

References

  • Weber JP, Wang S. Opt. 1990. p. 526. COI number [1:CAS:528:DyaK3cXks1OrsLY%3D]; Bibcode number [1990OptL...15..526W] [PubMed] [Cross Ref]
  • Avrutina EA, Gorfinkel VB, Luryi S, Shore KA. Appl. 1993. p. 2460. Bibcode number [1993ApPhL..63.2460A] [Cross Ref]
  • Yoon J, Lee W, Thomas EL. Nano Lett. 2006. p. 2211. COI number [1:CAS:528:DC%2BD28XptlektL8%3D]; Bibcode number [2006NanoL...6.2211Y] [PubMed] [Cross Ref]
  • Chena L, Toweb E. Appl. 2006. p. 053125. Bibcode number [2006ApPhL..89e3125C] [Cross Ref]
  • Koyama F, Kinoshita S, Iga K. Appl. 1989. p. 221. COI number [1:CAS:528:DyaL1MXkvVKqtLo%3D]; Bibcode number [1989ApPhL..55..221K] [Cross Ref]
  • Gourley PL, Brennan TM, Hammons BE, Corzine SW, Geels RS, Yan RH, Scott JW, Coldren LA. Appl. 1989. p. 1209. COI number [1:CAS:528:DyaL1MXitl2ltbc%3D]; Bibcode number [1989ApPhL..54.1209G] [Cross Ref]
  • Yan RH, Simes RJ, Coldren LA. Appl. 1989. p. 1946. COI number [1:CAS:528:DyaL1MXmsVersL8%3D]; Bibcode number [1989ApPhL..55.1946Y] [Cross Ref]
  • Wang B, Fei GT, Wang M, Kong MG, Zhang LD. Nanotechnology. 2007. p. 365601. Bibcode number [2007Nanot..18P5601W] [Cross Ref]
  • Hu X, Ling ZY, Chen SS, He XH. Chin. 2008. p. 3284. COI number [1:CAS:528:DC%2BD1cXhtF2iu7jM]; Bibcode number [2008ChPhL..25.3284H] [Cross Ref]
  • Zheng WJ, Fei GT, Wang B, Jin Z, Zhang LD. Mater. 2009. p. 706. COI number [1:CAS:528:DC%2BD1MXht1Glsro%3D] [Cross Ref]
  • Li AP, Müller F, Birner A, Nielsch K, Gösele U. J. 1998. p. 6023. COI number [1:CAS:528:DyaK1cXntlWhtL0%3D]; Bibcode number [1998JAP....84.6023L] [Cross Ref]
  • Li FY, Zhang L, Metzger RM. Chem. 1998. p. 2470. COI number [1:CAS:528:DyaK1cXltVGmt78%3D] [Cross Ref]
  • Aerts T, Dimogerontakis T, De Graeve I, Fransaer J, Terryn H. Surf. 2007. p. 7310. COI number [1:CAS:528:DC%2BD2sXkt1GgsLY%3D] [Cross Ref]
  • Snow PA, Squire EK, Russell PSt J, Canham LT. J. 1999. p. 1781. COI number [1:CAS:528:DyaK1MXkslyisLw%3D]; Bibcode number [1999JAP....86.1781S] [Cross Ref]
  • Donovan EP, Vechten DV, Kahn ADF, Carosella CA, Hubler GK. Appl. 1989. p. 2940. COI number [1:CAS:528:DyaL1MXlsVektrc%3D]; Bibcode number [1989ApOpt..28.2940D] [PubMed] [Cross Ref]

Articles from Nanoscale Research Letters are provided here courtesy of Springer
PubReader format: click here to try

Formats:

Related citations in PubMed

See reviews...See all...

Links

  • MedGen
    MedGen
    Related information in MedGen
  • PubMed
    PubMed
    PubMed citations for these articles

Recent Activity

Your browsing activity is empty.

Activity recording is turned off.

Turn recording back on

See more...